Jun 01, 2015 · EN 10088-2 1.4301 X5CrNi18-10 Stainless Steel is one of the the most widely used stainless steels and also known as 18/8 (Old name) which links to 18% chromium and 8% nickel. Where 1.4301 is the EN material number and X5CrNi18-10 is the steel designation name.
China 8crnis18-9 En 1.4305 Hot Rolled Structural Square 8CrNiS18-9 EN 1.4305 Hot Rolled Structural Square Steel Bar 1. Steel Grade:8CrNiS18-9 EN 1.4305 2. Product name:8CrNiS18-9 EN 1.4305 Hot Rolled Structural Square Steel Bar 3. Length:3000/6000/9000mm or asrequired 4. Diameter:1-2000mm Chemical composition % of grade X8CrNiS18-9 (1.4305):EN 10088-2-2005
It has the highest strength and lowest ductility compared to the other variants of EN 1.4305 stainless steel. The graph bars on the material properties cards below compare EN 1.4305 +C800 steel to:wrought austenitic stainless steels (top), all iron alloys (middle), and the entire database (bottom).
DIN EN 1.4305 Stainless Steel X8CrNiS18-9 Material DIN EN 1.4305 Stainless Steel X8CrNiS18-9 Material. DIN EN 1.4305 stainless steel (X8CrNiS18-9 material) is an European standard austenitic corrosion resisting material with sulfur added to improve cutting performance, but its corrosion resistance is limited in acid and chloride media, when used in these media, pitting or cavity corrosion can occur.
France AFNOR 1.4305, Austenite steel, NF EN 10088-1, NF 1.4305. France AFNOR NF EN 10088-1 NF EN 10088-2 NF EN 10088-3 NF EN 10088-5 NF EN 10297-2 (2005) 1.4305 Seamless circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 2:Stainless steel and Mechanical Properties, Chemical Element, Cross Reference, Datasheet.
replaced by 1.4301 EN 10088-2 states that Class A thickness tolerances shall normally be produced Surface Finish Standards have been extended and some changed 1.4305 303S31 303 58M 0.10x 18 8 . 0.35xS 190-230 500-700 35 1.4306 304L 0.030x 18 10 . . 200-250 500-670 45
Stainless Steel · Metalle Schmidt GmbHStainless Steel strips, sheets, coil, grade 409, 430, 441, 420, 631, 301, 301Mo, 304l, 304, 321, 316, 316Ti, 316l, 201, 202, 444, 310s. ASTM JIS GB DIN EN
Stainless Steel - Austenitic - 1.4301 (304) Sheet and Stainless steel types 1.4301 and 1.4307 are also known as grades 304 and 304L respectively. Type 304 is the most versatile and widely used stainless steel. It is still sometimes referred to by its old name 18/8 which is derived from the nominal composition of type 304 being 18% chromium and 8% nickel.
Datasheets for Flat Products Based on EN 10088-2 The table below contains all grades listed in EN 10088-2. In addition, there are some grades not in the current
Stainless Steel:Tables of Technical Properties Chemical and physical properties are in accordance with EN 10088-1:2005 Mechanical properties are in accordanc e with EN 10088-2:2005, except for he at resisting grad es (EN 100 95:1999) 1.4305 (3) 303 0,10 1,00 2,00 0,045 0,15 to 0,35
Surface Finish:1U 1C 1E 1D 1X 1G 2A 2H 2C 2D 2E 2B 2G 2P Finish for close tolerances. Unless otherwise agreed the surface roughness shall be Ra 1,2. 2P:Smoother and brighter than finish 2B or 2G. Free of surface defects. Finishes 2H, 2D, 2B or 2G, specular polishing:Products showing a well groomed surface appearance. Surface roughness shall be specified at the time of enquiry and order.
EN10088-1 X8CrNiS18-9material no 1.4305 Stainless steel EN10088-1 X8CrNiS18-9material no 1.4305Stainless steel is a kind of Austenitic Stainless Steel material. X8CRNIS18-9MATERIAL NO 1.4305 stainless steelchemical composition is :C Si Mn P S N Cr Mo Cu Ni Ti 0.1 1.00 2.00 0.045 0.015-0.351.4301, AISI 304, 1.4306, AISI 304L, 1.4305, AISI 303 1.4301, AISI 304, 1.4306, AISI 304L, 1.4305, AISI 303 - stainless steel X5CrNi18-10, 1.4301, AISI 304 - Austenitic stainless steel - base grade 18/8 for general industrial use together with X2CrNi18-9, 1